Atmel SAM4S-XPLD

Atmel SAM4S-XPLD (ATSAM4S-XPLD)

Atmel SAM4L Xplained Pro Evaluation Kit

Atmel SAM4L Xplained Pro Evaluation Kit (ATSAM4L-XPRO)

The Atmel^® SAM4L Xplained Pro evaluation kit is ideal for evaluation and prototyping with the SAM4L Cortex^™-M4 processor-based microcontroller.

The SAM4L Xplained Pro board is available as an Evaluation Kit or Starter Kit. You can also purchase extension boards individually.

Key Features

• Atmel SAM4LC4 microcontroller
• One mechanical reset button
• One mechanical user pushbutton (wake-up, bootloader entry or general purpose)
• One QTouch® button
• One yellow user LED
• USB interface, host and device function (shared physical interface)
• 32.768kHz crystal
• 12MHz crystal
• 4 Xplained Pro extension headers
• One custom extension header for segment LCD displays
• LDO/buck regulator mode selection
• LCD cluster power configuration option
• Embedded debugger
  • Auto-ID for board identification in Atmel Studio 6.1
  • One yellow status LED
  • One green board power LED
  • Symbolic debug of complex data types including scope information
  • Programming
  • Data Gateway Interface: USART, TWI, 4 GPIOs
  • Virtual COM port (CDC)
• USB powered
• Supported with application examples in Atmel Software Framework

Atmel SAM4S Xplained Pro Evaluation Kit (ATSAM4S-XPRO)

The Atmel^® SAM4S Xplained Pro evaluation kit is ideal for evaluating and prototyping with the SAM4S Cortex^™-M4 processor-based microcontroller.

The SAM4S Xplained Pro board is available as an Evaluation Kit or Starter Kit. You can also purchase extension boards individually.

Key Features

• Atmel SAM4SD32 microcontroller
• One reset button
• One user pushbutton (wake-up, bootloader entry or general purpose)
• One yellow user LED
• USB interface, end-point
• 2Gb NAND Flash
• 32.768kHz crystal
• 12MHz crystal
• SD card socket
• 3 Xplained Pro extension headers
• One display header
• One PIOD connector with all PIO signals
• One SPARE signal connector
• Embedded debugger
  • Auto-ID for board identification in Atmel Studio 6.1
  • One yellow status LED
  • One green board power LED
  • Symbolic debug of complex data types including scope information
  • Programming
  • Data Gateway Interface: SPI, TWI and 4 GPIOs
  • Virtual COM port (CDC)
• USB powered
• Supported with application examples in Atmel Software Framework

SAM3N-EK

Atmel SAM3N-EK (ATSAM3N-EK)

For evaluation and code development for applications running on a SAM3N device.

Atmel SAM3S-EK2

Atmel SAM3S-EK2 (ATSAM3S-EK2)

The SAM3S-EK2 enables evaluation and code development of applications running on a SAM3S and SAM3SD microcontroller.

Atmel SAM4L-EK (ATSAM4L-EK)

• ATSAM4LC4C Cortex-M4 device
• Board monitor with OLED color display, power measurement stage for ATSAM4LC4C power, joystick and five LEDS
• Segger J-Link OB Module (embedded debugger)
• QTouch slider and button
• Segment LCD (4x40)
• USB host and device
• Wireless 10-pin interface
• SPI serial Flash (AT25DF641A)
• Sensor Xplained support
• Light sensor
• Reset push button
• Audio jack connector
• User input push button
• RS485 connector

Atmel SAM4S-EK2

Atmel SAM4S-EK2 (ATSAM4S-EK2)

The SAM4S-EK enables evaluation and code development of applications running on a SAM4S microcontroller.

The SAM4S-EK includes hardware such as:

• SAM4SD32C chip in an LQFP100 package with optional socket footprint
• 12 MHz crystal
• 32.768 KHz crystal
• Optional SMB connector for external system clock input
• NAND Flash
• 2.8” TFT color LCD display with touch panel and backlight
• UART port with level shifter circuit
• USART port with level shifter circuit multiplexed with RS485 port with level shifter circuit
• Microphone input and mono/stereo headphone jack output
• SD/MMC interface
• Reset button: NRST
• User buttons: Left and Right
• QTouch^® buttons: Up, Down, Left, Right, Valid and Slider
• Full Speed USB device port
• JTAG/ICE port
• On-board power regulation
• BNC connector for ADC input
• BNC connector for DAC output
• User potentiometer connected to the ADC input
• ZigBee^® connector

AT91SAM7SE-EK

The AT91SAM7SE-EK Evaluation Kit enables the evaluation of and code development for applications running on an AT91SAM7SE device.

AT91SAM7X-EK

The AT91SAM7X-EK evaluation kit enables evaluation capabilities and code development of applications running on an AT91SAM7X microcontroller.

ATSAM3U-EK

The SAM3U-EK evaluation kit enables evaluation capabilities and code development of applications running on an ATSAM3U device.

Atmel SAM4E-EK

Atmel SAM4E-EK (ATSAM4E-EK)

The SAM4E-EK enables evaluation and code development of applications running on a SAM4E microcontroller.

The SAM4E-EK includes hardware such as:

• SAM4E16 chip BGA144 package with optional socket footprint
• 12MHz crystal
• 32.768kHz crystal
• Optional SMB connector for external system clock input
• NAND Flash
• 2.8” TFT color LCD display with touch panel and backlight
• One Ethernet physical transceiver layer with RJ45 connector
• UART port with RS232 driver
• USART port with RS232 driver multiplexed with RS485 function with driver
• CAN port with driver
• Mono/stereo headphone jack output
• SD/MMC interface
• Reset button: NRST
• User buttons: WAKU, TAMP, Scroll-up, Scroll-down
• QTouch^® buttons: Left, Right and Slider
• Full Speed USB device port
• JTAG/ICE port
• On-board power regulation
• Three user LEDs
• Power LED
• BNC connector for ADC input
• BNC connector for DAC output
• User potentiometer connected to the ADC input
• ZigBee^® connector
• PIO connection interfaces (PIOA, PIOC and PIOD with 32-bit, PIOB with 16-bit PIOE with 6-bit)

Atmel SAM4S-WPIR-RD

Atmel SAM4S-WPIR-RD (ATSAM4S-WPIR-RD)

The SAM4S-WPIR-RD Reference Design Kit is based on SAM4S16C device. Thanks to this reference design, you will be able to develop your own PIR motion detector camera.

The SAM4S-WPIR-RD includes battery holder, LDO, image sensor, 1M byte SRAM, PIR sensor, JTAG connector, QVGA LCD, ZigBee connector.

Atmel SAM9CN11-EK

Atmel SAM9CN11-EK (AT91SAM9CN11-EK)

The SAM9CN11-EK evaluation kit enables rapid evaluation and code development of applications running on a SAM9CN11 or a SAM9CN12 device.

• Atmel SAM9CN11 microcontroller in BGA217 package
• 16MHz crystal
• 32.768kHz crystal
• Memory — 1Gb DDR2 memory; 2Gb NAND Flash memory with Chip Selection control switch; Optional NOR flash; 32Mb SPI Serial DataFlash with Chip Selection control switch; 512Kb Serial EEPROM; 1Kb 1-Wire EEPROM; SD/MMC interface
• Communication — One Ethernet Physical Transceiver Layer with RJ45 connector; UART DBGU port with level shifter IC; JTAG/ICE port; USB Host and Device; ZigBee®
• Add-on display module — TFT LCD module with touch; QTouch elements for user QTouch: (K1 to K4)
• Audio codec with input stereo headphone and microphone
• On-board power regulation and backup battery
• Two user LEDs and one power LED
• System buttons: NRST

Atmel SAM9N12-EK

Atmel SAM9N12-EK (AT91SAM9N12-EK)

SKU: AT91SAM9N12-EK

The SAM9N12-EK enables evaluation and code development of applications running on a SAM9N12 microcontroller

Following is the list of the SAM9N12 Evaluation Kit features:

·     SAM9N12 microcontroller BGA

16 MHz crystal

32.768 KHz crystal

·     Memory

1Gb DDR2 memory

2Gb NAND Flash memory with Chip Selection control switch

Optional NOR flash

32Mb SPI Serial Data flash with Chip Selection control switch

512Kb Serial EEPROM 1Kb 1-Wire EEPROM

SD/MMC interface

·     Communication

One Ethernet Physical Transceiver Layer with RJ45 connector

UART DBGU port with level shifter IC

JTAG/ICE port

USB Host and Device ZigBee®

·     Add on Display module TFT LCD module with touch screen QTouch elements as for user QTouch: (K1 to K4)

·     Audio codec with input stereo headphone and microphone

·     On-board power regulation and Backup Battery

·     Two user LEDs and one power LED

·     System buttons: NRST, WKUP, OE_CS,

·     One User buttons

Atmel SAM9X25-EK

Atmel SAM9X25-EK (AT91SAM9X25-EK)

For evaluation and code development for applications running on a SAM9X25 device.

Following is the list of the CPU Module board components:

• Embedded MPU SAM9X25
• 12 MHz crystal
• 32.768 KHz crystal
• 1 Gbit DDR2 memory
• 2 Gits NAND Flash memory with Chip Selection control switch
• 32 Mbits SPI Serial DataFlash with Chip Selection control switch
• 512 Kbits EEPROM
• 1 Kbyte 1-Wire EEPROM
• On-board power regulation
• Two user LEDs
• PHY

Following is the list of the board features:

• MII/RMII Ethernet 10/100 w/PHY and three Led status
• RMII Ethernet 10/100 w/PHY and three Led status
• RS232 four wires/RS485 Shared interface
• RS232 four wires
• RS232 two wires
• CAN interface Shared interface
• 2 * USB 2.0 Host
• 1 * USB 2.0 Host/Device
• Software Modem Device
• µSD Card Slot Onboard
• MMC/MMC+/SD/SDIO/CE-ATA
• ZigBee®
• SPI
• TWI
• JTAG Test Access Port

Atmel SAM9G25-EK

Atmel SAM9G25-EK (AT91SAM9G25-EK)

For evaluation and code development for applications running on a SAM9G25 device.

Atmel SAMA5D35-EK

Atmel SAMA5D35-EK (ATSAMA5D35-EK)

AT91SAM9260-EK

The AT91SAM9260-EK Evaluation Kit enables the evaluation of and code development for applications running on an AT91SAM9260 device.

AT91SAM9G20-EK

The AT91SAM9G20-EK Evaluation Kit supports the AT91SAM9G20 ARM926EJ-S-based 32-bit RISC microcontroller for real-time code development and evaluation.

AT91SAM9XE-EK

The AT91SAM9XE-EK Evaluation Kit enables the evaluation of and code development for applications running on an AT91SAM9XE device.