2.4 GHz Wi-Fi and Bluetooth combo chip – ESP32

Espressif

ESP32 SoC

esp32

  • 2.4 GHz Wi-Fi and Bluetooth combo chip
  • TSMC low power 40nm technology
  • Best power performance and RF performance
  • Robustness, versatility and reliability

High Level of Integration

ESP32 is highly-integrated with in-built antenna switches, RF balun, power amplifier, low-noise receive amplifier, filters, and power management modules. ESP32 adds priceless functionality and versatility to your applications with minimal Printed Circuit Board (PCB) area requirements.

Hybrid Wi-Fi & Bluetooth

ESP32 can perform as a complete standalone system or as a slave device to a host MCU, reducing communication stack overhead on the main application processor. ESP32 can interface with other systems to provide Wi-Fi and Bluetooth functionality through the SPI / SDIO or I2C / UART interfaces.

Ultra-Low Power Management

Engineered for mobile devices, wearable electronics and IoT applications, ESP32 achieves ultra-low power consumption with a combination of several types of proprietary software. The state-of-the-art power saving features include fine resolution clock gating, power modes, and dynamic power scaling.

Robust Design

ESP32 is capable of functioning reliably in industrial environments with an operating temperature ranging from -40°C to +125°C. Powered by advanced calibration circuitries, ESP32 can dynamically remove external circuit imperfections or adapt to changes in external conditions.


ESP-WROOM-32

Powered by Espressif’s most advanced SoC, the ESP-WROOM-32 features high performance, a wide range of peripherals, Wi-Fi and Bluetooth radio, which provide a complete solution tailored to advanced IoT applications.

esp-wroom-32-banner_0

Compact Design

The ESP-WROOM-32, measuring 25.2mm x 18mm only, contains the ESP32 SoC, flash memory, precision discrete components, and PCB antenna to provide outstanding RF performance in space-constraint applications.

Optimized Layout

The ESP-WROOM-32 pinout is optimized, since peripheral IO pads are grouped and led out to facilitate application board design with minimal external trace routing, thus making the application even more compact.

Open and Free

We’re going open source yet again! The ESP-WROOM-32 schematics and PCB layout are freely available for download and may be used as a design reference for developing fully- customized ESP32-based hardware designs.

Application Ready

Suitable for commercial application development with a robust 4-layer FCC, CE ( RED ), IC, TELEC, SRRC & KCC compliant design and wide operating temperature range of -40°C to 85°C.
 

ESP32-DevKitC

Jump right into what matters - start prototyping with our latest SoC, the ESP32.

ESP32-DevKitC is a low-footprint, minimal system development board which is powered by our latest ESP-WROOM-32 module and can be easily adjusted to a breadboard.

wroom-32-banner
 

New and Powerful

Built around the ESP-WROOM-32, this minimal system development board achieves optimal performance with its rich peripheral set, Wi-Fi and Bluetooth radio solutions, which are offered by our latest SoC, the ESP32. The limit is your imagination!

Rapid Prototyping

Get right into application design and development without worrying about RF performance and antenna design. The ESP32-DevKitC has your basic system requirements already covered. Just plug in the USB cable and you’re good to go!

Flexible and Feature-Rich

The ESP32-DevKitC contains the entire basic support circuitry for the ESP-WROOM-32, including the USB-UART bridge, reset- and boot-mode buttons, LDO regulator and a micro-USB connector. Every important GPIO is available to the developer.

Breadboard-Friendly

The ESP32-DevKitC pinout is optimized for prototyping on a breadboard. The on-board LDO output is led out for powering additional off-board electronics. Peripheral outputs are grouped together for hassle-free prototyping.


ESP-WROVER-KIT

The new ESP-WROVER-KIT supports the most distinguishing features of the ESP32. Whether you need external pSRAM for IoT applications, or an LCD+camera interface, we have you covered!

esp-wrover-kit1
 

Built-in USB-JTAG Debugger

Bogged down in bugs? We came up with a solution! The ESP32 supports JTAG debugging, while the ESP-WROVER-KIT integrates a USB debugger, as well. This makes debugging and tracing complex applications very easy, without the need for any additional hardware.

Advanced Hardware

ESP32 is engineered to be fast, smart and versatile. The ESP-WROVER-KIT complements these characteristics by offering an on-board high-speed Micro-SD card interface, VGA camera interface, as well as a 3.2” SPI LCD panel and I/O expansion capabilities.

Wide Compatibility

Have you been developing your applications around the ESP-WROOM-32 module? Not only does the ESP-WROVER-KIT support the popular ESP-WROOM-32 module, but it also supports the new ESP32-WROVER module, which is coming soon!

Online-Shop
Ineltek auf Youtube
Recent Popular Info

Total subscribers:
4

Total uploads:
48

Total upload views:
671

Direktanfrage
Technische Anfrage
Termine